Instant weight loss and no strict diet with Tillett Seats!

These are looking like very nice seats and Lotus recently made them even more appealing. I was planning on ordering Alcantara seats in a Base Emira. However, after loooking at the Base price list and seeing that Lotus is asking $2,500.00 USD for their Alcantara seats, I'd rather put that money toward Tillett's.
 
These are looking like very nice seats and Lotus recently made them even more appealing. I was planning on ordering Alcantara seats in a Base Emira. However, after loooking at the Base price list and seeing that Lotus is asking $2,500.00 USD for their Alcantara seats, I'd rather put that money toward Tillett's.
If I had to spec from a base model, 100% that would be how I'd configure.
 
Steve, Have you resolved the warning lights for the airbag? Is there a plug and play solution yet?
 
Steve, Have you resolved the warning lights for the airbag? Is there a plug and play solution yet?
I have fitted the GRP resistor plugs.

The car is currently in Bell & Covill having some other work done and I have asked them to clear the air bag fault light down, then we will then see if they work. I have had this sign up for over a year. I don't even notice it now but it would be good to get it out of the way. I drove the courtesy car back five minutes ago and after my spine wallowing around in no mans land for an hour, I can confidently assure you that a small notification on the dash is a small price to pay.
 
Received a pair of seats today, and my first impression is.... Can't wait to put them on but can't, as only one runner set is included. Let's hope they'll resolve this soon enough.
 
Received a pair of seats today, and my first impression is.... Can't wait to put them on but can't, as only one runner set is included. Let's hope they'll resolve this soon enough.
Is that my company or did you buy them from elsewhere? I will look into that for you if they were bought directly from us.
 
Is that my company or did you buy them from elsewhere? I will look into that for you if they were bought directly from us.
It is from Tillett directly :). I have already contacted CS but obviously any additional nudges would be highly appreciated.

Thanks Steve!
 
I have fitted the GRP resistor plugs.

The car is currently in Bell & Covill having some other work done and I have asked them to clear the air bag fault light down, then we will then see if they work. I have had this sign up for over a year. I don't even notice it now but it would be good to get it out of the way. I drove the courtesy car back five minutes ago and after my spine wallowing around in no mans land for an hour, I can confidently assure you that a small notification on the dash is a small price to pay.
The resistor from GRP is only for the drivers side, correct? I don’t believe they have released the passenger side bypass kit.
 
It is from Tillett directly :). I have already contacted CS but obviously any additional nudges would be highly appreciated.

Thanks Steve!
I have already contacted my office.
Hopefully they will get to the bottom of it and get back to you quickly.
If you do not get a satisfactory response please email me.
[email protected]
 
The resistor from GRP is only for the drivers side, correct? I don’t believe they have released the passenger side bypass kit.
I fitted them to both sides as two sets were sent to me. I just heard from the dealer that a number of error codes have been deleted but not all of them.
 
Update: They found where the runner was hiding and it's on the way to me now. Pretty impressive customer service I must say.
Installation log: Stuck. Just when I thought I was 99% done, I realized that I couldn't engage the cross bar to adjust the seat position. Apparently the cross bar seems to be too big and interferes with part of the bracket.
1000005514.jpg
1000005515.jpg
1000005516.jpg
 
Installation log: Stuck. Just when I thought I was 99% done, I realized that I couldn't engage the cross bar to adjust the seat position. Apparently the cross bar seems to be too big and interferes with part of the bracket.
View attachment 53257View attachment 53259View attachment 53260
That should work. It’s close but I’ve not had any problems yet. It might be the handle bend.
Please feel free to email me and we will look at it more closely.
[email protected]
 
Yes, but my cross bar is wider (or the bracket narrower) than yours. I ended up cutting 1.5 cm off the ends of the cross bar to make it work.

You can see the scratch from before the cut.
1000005529.jpg
 
Awesome! Is there a link for the harness bar? I need one. Or better yet a half cage.
Jubu offers those as well

 

Create an account or login to comment

Join now to leave a comment enjoy browsing the site ad-free!

Create account

Create an account on our community. It's easy!

Log in

Already have an account? Log in here.

Back
Top